Toyota
Showing 577–588 of 1521 results
-
Drop Links AE111
€18.45 – €32.45Each drop link sold separately. price per single drop link
Drop link for AE111 Levin and Trueno
Available for front superstrut and non superstrut. Rear drop link is the same for super strut and non super strut models.
-
Drop Links AE86 Ke70 Front
€30.00 (excl. VAT €24.39)Sold as a pair
-
Drop Links AE92
€18.45Anti Roll Bar Drop Links for AE92 GTI Corolla
Each drop link sold seperatly
-
Drop Links Front JZX81
€38.89 (excl. VAT €31.62)Pair of front drop links for Toyota Chaser, Cresta, Cressida, JZX81, GX81 and MX83
-
ECU Engine Temperature Sensor 4AGE 16V
€20.00 (excl. VAT €16.26)Suitable for 4age 16v ae86 only
-
Engine Assembly Lube / Lubricant Lucas
€15.74 (excl. VAT €12.80)Engine Assembly lube 237ml
-
Engine Back Plate 3SGE J160
€37.00 (excl. VAT €30.08)SQ SEALING PLATE, SUIT 3SGE ENGINE TO j160 GEARBOX
The bottom half of a J160 bellhousing when fitted to a Beams engine is sealed off with part of the sump itself. This part of the sump is a hollow housing that curves down and can be readily cut into or fully removed. However this can pose an issue during an engine conversion in one of two situations below.
3sge Beams engine: Often during an engine / gearbox conversions this lower part of the sump is cut into to clear steering systems, once cut it opens the cavity leading into the bellhousing. Alternatively if the sump has been changed to a different type the same applies as below.
Other S-series engines: If the J160 gearbox has been fitted to any other S-series engine with a different sump then a whole section of the bellhousing will be left exposed.
With either of the situations above it exposes the clutch area to debris. This leaves the flywheel and clutch both
The bottom half of a J160 bellhousing when fitted to a Beams engine is sealed off with part of the sump itself. This part of the sump is a hollow housing that curves down and can be readily cut into or fully removed. However this can pose an issue during an engine conversion in one of two situations below.
3sge Beams engine: Often during an engine / gearbox conversions this lower part of the sump is cut into to clear steering systems, once cut it opens the cavity leading into the bellhousing. Alternatively if the sump has been changed to a different type the same applies as below.
Other S-series engines: If the J160 gearbox has been fitted to any other S-series engine with a different sump then a whole section of the bellhousing will be left exposed.
With either of the situations above it exposes the clutch area to debris. This leaves the flywheel and clutch both vunerable to damage from grit making it’s way between the friction surfaces.
to damage from grit making it’s way between the friction surfaces.
It’s a sandwich plate that is fitted directly on top of the existing plate that is bolted to the block. Once installed this will seal off the whole transmission face.
-
Engine Back Plate 4AGE
€29.00 (excl. VAT €23.58)4AGE Engine back plate
This plate is fitted between 4AGE Engine and T50 Gearbox
These plates are often damaged, bent or missing from engines which can cause debris, dirt and oil to enter the bellhousing which can cause damage to clutch, flywheel or gearbox.
Suitable for all 4AGE 16V and 20v engines where the starter is mounted on the exhaust side of the engine only
-
Engine Bay Blanking Kit AE86
€32.00 (excl. VAT €26.02)16 piece engine bay blanking plate kit
Blanks all those unnecessary wiring harness, heater and cable holes, ideal for rally and race car builds
-
Engine Bolt Kit 4AGE 16V
€215.00 (excl. VAT €174.80)Engine bolt kit for Toyota 4AGE 16V AE86 TVIS Engine
This kit includes the following new nuts and bolts to have your engine looking like new:
-Intake Manifold
-Water pump
-Crank pulley, water pump pulley, camshaft pulleys, timing belt tensioner
-Rocker covers and spark plug cover
-Exhaust manifold
-Cylinder head water outlets
-Distributor
-Throtthle body and ISCV
-Engine hooks and Coolant drain plug
-Fuel Rail
-Timing cover and back plate
-Oil Pump
-Rear crank seal housing
-Sump
-Right Engine Mount
-Left Engine Mount
-Alternator
All of the above comes sorted and labelled in a 15 compartment assortment box -
Engine Bolt Kit 4AGE 20V
€215.00 (excl. VAT €174.80)Engine bolt kit for Toyota 4AGE 20V Engine in RWD formatThis kit includes the following new nuts and bolts to have your engine looking like new:
-Intake Manifold
-Water pump
-Crank pulley, water pump pulley, camshaft pulleys
-Rocker cover
-Exhaust manifold
-Cylinder head water outlets
-Distributor
-Throttle bodys and ISCV
-Engine hooks-Coolant drain plug & TPS
-Timing cover and back plate
-Oil Pump
-Rear crank seal housing
-Sump
-Right Engine Mount
-Left Engine Mount
-Alternator
All of the above comes sorted and labelled in a 15 compartment assortment boxThis kit is designed to be used on a 4AGE 20V engine in a rwd car using flos rwd conversion parts.If you intend using this bolt kit in a FWD car some bolts and lengths may not suit. -
Engine Gasket Kit 1E
€95.50 (excl. VAT €77.64)Engine Gasket Kit for Toyota 1E engine
Showing 577–588 of 1521 results