1GGTE / 1GGZE
Showing 13–24 of 71 results
-
Crankshaft Bearings 1G 1GFE 1GGZE 1GGTE
€17.99 – €146.00Crankshaft bearings for Toyota 1G , 1GG , 1GFE , 1GGZE and 1GGTE
Please read below and make sure to select the correct bearings for your engine
- Trust Washers suitable for all 1G , 1GG , 1GFE , 1GGZE and 1GGTE engines
- Con Rods Bearings Available in 42mm and 44mm Rod Journal Size
- Main Bearings Available in Type A and Type B and Type C
- Type A Set of 7 Main Bearings with a width of 19mm (commonly found in early year engines)
- Type B Set of 6 Main Bearings with a width of 19mm and 1 Main Bearing with a width of 22mm
- Type C Set of 6 Main Bearings with a width of 18mm and 1 Main Bearings with a width of 22mm
All bearings are sold as Standard size. If you require 0.25 oversize please email sales@flos.ie
IS200 1GFE VVTI Engines require Type C Main Bearing and 44mm Con Rod Bearing
-
Crankshaft Key Way 1GGTE 1GGZE 1GFE
€5.52 (excl. VAT €4.49) -
Crankshaft Pulley / Timing Belt Gear Removal Tool 4AGE
€55.90 (excl. VAT €45.45) -
Crankshaft Pulley Timing Belt Gear 1GGTE 1GGZE
€137.38 (excl. VAT €111.69)Crankshaft pulley gear for timing belt
Suitable for 1GGTE and 1GGZE engines
-
Dirko Gasket Sealant
€6.94 (excl. VAT €5.64)Dirko Gasket Sealant
Dirko is used by Toyota for sealing sump / oil pans from factory
Can be used for sealing oil and water
-
Distributor Cap 1GGTE
€64.34 (excl. VAT €52.31)Distributor cap for Toyota 1G-GTE Engine
-
Driveshaft Slip Yoke setup R154
€195.00 (excl. VAT €158.54)This part is required when fitting an R154 Gearbox into a car where a custom length propshaft is required.Parts Included are:1x R154 Slip Yoke1x Universal Joint1x Weld Yoke4x Snap RingsThe propshaft can be made to your required length by Driveshaft Services Dublin or Charleville Drive Shafts Cork.(Flos does not offer this service) -
Engine Assembly Lube / Lubricant Lucas
€15.74 (excl. VAT €12.80)Engine Assembly lube 237ml
-
Engine Gasket Kit 1GGTE
€182.10 – €440.00Engine Gasket Kit for Toyota 1GGTE
Available with Graphite Head Gasket or Multi Layer Steel Head Gasket 1.2mm
-
Engine Stand Mounting Bolts
€12.00 (excl. VAT €9.76)These bolts are required when mounting your Toyota Engine on an Engine Stand.
100mm in length
Sold as a set of 4 -
Exedy Clutch Kit 1GGTE
€247.09 (excl. VAT €200.89)Exedy 3 piece clutch to suit 1GGTE
Suitable for engines with 236mm flywheel only (236mm clutch surface diameter)
-
Exhaust System Gasket HKS
€24.00HKS exhaust system gaskets
2 gaskets per pack
Gaskets suit most Japanese exhaust systems
Available for 50mm , 60mm and 75mm diameter systems
Showing 13–24 of 71 results